[profile] layer_height = 0.2 wall_thickness = 0.8 retraction_enable = True solid_layer_thickness = 0.6 fill_density = 50 nozzle_size = 0.4 print_speed = 130 print_temperature = 225 print_temperature2 = 0 print_temperature3 = 0 print_temperature4 = 0 print_bed_temperature = 70 support = None platform_adhesion = None support_dual_extrusion = False filament_diameter = 2.92 filament_diameter2 = 0 filament_diameter3 = 0 filament_diameter4 = 0 filament_flow = 110 retraction_speed = 40 retraction_amount = 4.5 retraction_dual_amount = 16.5 bottom_thickness = 0.3 object_sink = 0.0 overlap_dual = 0.2 travel_speed = 170 bottom_layer_speed = 40 infill_speed = 0.0 cool_min_layer_time = 2 fan_enabled = True skirt_line_count = 2 skirt_gap = 3.0 fan_layer = 1 fan_speed = 100 fan_speed_max = 100 cool_min_feedrate = 10 cool_head_lift = False solid_top = True solid_bottom = True fill_overlap = 25 support_rate = 50 brim_line_count = 20 raft_margin = 5 raft_line_spacing = 1.0 raft_base_thickness = 0.3 raft_base_linewidth = 0.7 raft_interface_thickness = 0.2 raft_interface_linewidth = 0.2 fix_horrible_union_all_type_a = False fix_horrible_union_all_type_b = False fix_horrible_use_open_bits = False fix_horrible_extensive_stitching = False plugin_config = (lp1 . object_center_x = -1 object_center_y = -1 [alterations] start.gcode = ;Sliced {filename} at: {day} {date} {time} ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density} ;Print time: {print_time} ;Filament used: {filament_amount}m {filament_weight}g ;Filament cost: {filament_cost} M92 X79.1359 Y79.1359 Z526.112 E826.5 G21 ;metric values G90 ;absolute positioning M107 ;start with the fan off G28 X0 Y0 ;move X/Y to min endstops G28 Z0 ;move Z to min endstops G92 X0 Y0 Z0 E0 ;reset software position to front/left/z=0.0 G1 Z15.0 F{max_z_speed} ;move the platform down 15mm G92 E0 ;zero the extruded length G1 F200 E3 ;extrude 3mm of feed stock G92 E0 ;zero the extruded length again ;go to the middle of the platform (disabled, as there is no need to go to the center) ;G1 X{machine_center_x} Y{machine_center_y} F{travel_speed} G1 F{travel_speed} end.gcode = ;End GCode M104 S0 ;extruder heater off M140 S0 ;heated bed heater off (if you have it) G91 ;relative positioning G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way M84 ;steppers off G90 ;absolute positioning start2.gcode = ;Sliced at: {day} {date} {time} ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density} ;Print time: {print_time} ;Filament used: {filament_amount}m {filament_weight}g ;Filament cost: {filament_cost} G21 ;metric values G90 ;absolute positioning M107 ;start with the fan off G28 X0 Y0 ;move X/Y to min endstops G28 Z0 ;move Z to min endstops G1 Z15.0 F{travel_speed} ;move the platform down 15mm T1 G92 E0 ;zero the extruded length G1 F200 E10 ;extrude 10mm of feed stock G92 E0 ;zero the extruded length again G1 F200 E-{retraction_dual_amount} T0 G92 E0 ;zero the extruded length G1 F200 E10 ;extrude 10mm of feed stock G92 E0 ;zero the extruded length again G1 F{travel_speed} M117 Printing... end2.gcode = ;End GCode M104 T0 S0 ;extruder heater off M104 T1 S0 ;extruder heater off M140 S0 ;heated bed heater off (if you have it) G91 ;relative positioning G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way M84 ;steppers off G90 ;absolute positioning support_start.gcode = support_end.gcode = cool_start.gcode = cool_end.gcode = replace.csv = nextobject.gcode = ;Move to next object on the platform. clear_z is the minimal z height we need to make sure we do not hit any objects. G92 E0 G91 ;relative positioning G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure G1 Z+0.5 E-5 F{travel_speed} ;move Z up a bit and retract filament even more G90 ;absolute positioning G1 Z{clear_z} F{max_z_speed} G92 E0 G1 X{machine_center_x} Y{machine_center_y} F{travel_speed} G1 F200 E5 G92 E0 switchextruder.gcode = ;Switch between the current extruder and the next extruder, when printing with multiple extruders. G92 E0 G1 E-36 F5000 G92 E0 T{extruder} G1 X{new_x} Y{new_y} Z{new_z} F{travel_speed} G1 E36 F5000 G92 E0