;A20 PAD application ;------------------------------------------------------------------------------- ; 说明： ; 1. 脚本中的字符串区分大小写，用户可以修改"="后面的数值，但是不要修改前面的字符串 ; 2. 新增主键和子键的名称必须控制在32个字符以内，不包括32个 ; 3. 所以的注释以“;”开始，单独占据一行 ; 4. 注释不可和配置项同行，例如：主键和子健后面不能添加任何形式的注释 ; ; gpio的描述形式：Port:端口+组内序号<功能分配><内部电阻状态><驱动能力><输出电平状态> ; 例如：port:PA0<0> ;------------------------------------------------------------------------------- [product] version = "100" machine = "cubietruck" [platform] eraseflag = 0 [target] boot_clock = 912 dcdc2_vol = 1450 dcdc3_vol = 1300 ldo2_vol = 3000 ldo3_vol = 2800 ldo4_vol = 2800 storage_type = 0 [clock] pll3 = 297 pll4 = 300 pll6 = 600 pll7 = 297 pll8 = 336 [card_boot] logical_start = 40960 sprite_gpio0 = [card0_boot_para] card_ctrl = 0 card_high_speed = 1 card_line = 4 sdc_d1 = port:PF0<2><1> sdc_d0 = port:PF1<2><1> sdc_clk = port:PF2<2><1> sdc_cmd = port:PF3<2><1> sdc_d3 = port:PF4<2><1> sdc_d2 = port:PF5<2><1> [card2_boot_para] card_ctrl = 2 card_high_speed = 1 card_line = 4 sdc_cmd = port:PC6<3><1> sdc_clk = port:PC7<3><1> sdc_d0 = port:PC8<3><1> sdc_d1 = port:PC9<3><1> sdc_d2 = port:PC10<3><1> sdc_d3 = port:PC11<3><1> [twi_para] twi_port = 0 twi_scl = port:PB0<2> twi_sda = port:PB1<2> [uart_para] uart_debug_port = 0 uart_debug_tx = port:PB22<2><1> uart_debug_rx = port:PB23<2><1> [uart_force_debug] uart_debug_port = 0 uart_debug_tx =port:PF2<4><1> uart_debug_rx =port:PF4<4><1> [jtag_para] jtag_enable = 0 jtag_ms = port:PB14<3> jtag_ck = port:PB15<3> jtag_do = port:PB16<3> jtag_di = port:PB17<3> ;--------------------------------------------------------------------------------------------------------- ; if 1 == standby_mode, then support super standby; ; else, support normal standby. ;--------------------------------------------------------------------------------------------------------- [pm_para] standby_mode = 0 ;------------------------------------------------------------------------------- ;sdram configuration ;------------------------------------------------------------------------------- [dram_para] dram_baseaddr = 0x40000000 dram_clk = 432 dram_type = 3 dram_rank_num = 0xffffffff dram_chip_density = 0xffffffff dram_io_width = 0xffffffff dram_bus_width = 0xffffffff dram_cas = 9 dram_zq = 0x7f dram_odt_en = 0 dram_size = 0xffffffff dram_tpr0 = 0x42d899b7 dram_tpr1 = 0xa090 dram_tpr2 = 0x22a00 dram_tpr3 = 0x0 dram_tpr4 = 0x1 dram_tpr5 = 0x0 dram_emr1 = 0x4 dram_emr2 = 0x10 dram_emr3 = 0x0 ;------------------------------------------------------------------------------- ;Mali configuration ;------------------------------------------------------------------------------- [mali_para] mali_used = 1 mali_clkdiv = 1 ;------------------------------------------------------------------------------- ;Ethernet MAC configuration ;------------------------------------------------------------------------------- [gmac_para] gmac_used = 1 gmac_rxd3 = port:PA00<5><3> gmac_rxd2 = port:PA01<5><3> gmac_rxd1 = port:PA02<5><3> gmac_rxd0 = port:PA03<5><3> gmac_txd3 = port:PA04<5><3> gmac_txd2 = port:PA05<5><3> gmac_txd1 = port:PA06<5><3> gmac_txd0 = port:PA07<5><3> gmac_rxclk = port:PA08<5><3> gmac_rxerr = port:PA09<0><3> gmac_rxctl = port:PA10<5><3> gmac_mdc = port:PA11<5><3> gmac_mdio = port:PA12<5><3> gmac_txctl = port:PA13<5><3> gmac_txclk = port:PA14<0><3> gmac_txck = port:PA15<5><3> gmac_clkin = port:PA16<5><3> gmac_txerr = port:PA17<0><3> ;------------------------------------------------------------------------------- ;i2c configuration ;------------------------------------------------------------------------------- [twi0_para] twi0_used = 1 twi0_scl = port:PB0<2> twi0_sda = port:PB1<2> [twi1_para] twi1_used = 0 twi1_scl = port:PB18<2> twi1_sda = port:PB19<2> [twi2_para] twi2_used = 0 twi2_scl = port:PB20<2> twi2_sda = port:PB21<2> ;------------------------------------------------------------------------------- ;uart configuration ;uart_type --- 2 (2 wire), 4 (4 wire), 8 (8 wire, full function) ;------------------------------------------------------------------------------- [uart_para0] uart_used = 1 uart_port = 0 uart_type = 2 uart_tx = port:PB22<2><1> uart_rx = port:PB23<2><1> [uart_para1] uart_used = 0 uart_port = 1 uart_type = 8 uart_tx = port:PA10<4><1> uart_rx = port:PA11<4><1> uart_rts = port:PA12<4><1> uart_cts = port:PA13<4><1> uart_dtr = port:PA14<4><1> uart_dsr = port:PA15<4><1> uart_dcd = port:PA16<4><1> uart_ring = port:PA17<4><1> [uart_para2] uart_used = 1 uart_port = 2 uart_type = 4 uart_tx = port:PI18<3><1> uart_rx = port:PI19<3><1> uart_rts = port:PI16<3><1> uart_cts = port:PI17<3><1> [uart_para3] uart_used = 0 uart_port = 3 uart_type = 4 uart_tx = port:PH00<4><1> uart_rx = port:PH01<4><1> uart_rts = port:PH02<4><1> uart_cts = port:PH03<4><1> [uart_para4] uart_used = 0 uart_port = 4 uart_type = 2 uart_tx = port:PH04<4><1> uart_rx = port:PH05<4><1> [uart_para5] uart_used = 0 uart_port = 5 uart_type = 2 uart_tx = port:PH06<4><1> uart_rx = port:PH07<4><1> [uart_para6] uart_used = 0 uart_port = 6 uart_type = 2 uart_tx = port:PA12<4><1> uart_rx = port:PA13<4><1> [uart_para7] uart_used = 0 uart_port = 7 uart_type = 2 uart_tx = port:PA14<4><1> uart_rx = port:PA15<4><1> ;------------------------------------------------------------------------------- ;spi configuration ;------------------------------------------------------------------------------- [spi0_para] spi_used = 0 spi_cs_bitmap = 1 spi_cs0 = port:PI10<2> spi_cs1 = port:PI14<2> spi_sclk = port:PI11<2> spi_mosi = port:PI12<2> spi_miso = port:PI13<2> [spi1_para] spi_used = 0 spi_cs_bitmap = 1 spi_cs0 = port:PA00<3> spi_cs1 = port:PA04<3> spi_sclk = port:PA01<3> spi_mosi = port:PA02<3> spi_miso = port:PA03<3> [spi2_para] spi_used = 0 spi_cs_bitmap = 1 spi_cs0 = port:PC19<3> spi_cs1 = port:PB13<2> spi_sclk = port:PC20<3> spi_mosi = port:PC21<3> spi_miso = port:PC22<3> [spi3_para] spi_used = 0 spi_cs_bitmap = 1 spi_cs0 = port:PA05<3> spi_cs1 = port:PA09<3> spi_sclk = port:PA06<3> spi_mosi = port:PA07<3> spi_miso = port:PA08<3> ;------------------------------------------------------------------------------- ;capacitor tp configuration ;external int function ;wakeup output function ;notice: ; tp_int_port & tp_io_port use the same port ;------------------------------------------------------------------------------- [ctp_para] ctp_used = 0 ctp_name = "gt811" ctp_twi_id = 2 ctp_twi_addr = 0x40 ctp_screen_max_x = 1024 ctp_screen_max_y = 600 ctp_revert_x_flag = 0 ctp_revert_y_flag = 0 ctp_exchange_x_y_flag = 1 ctp_firm = 1 ctp_int_port = port:PH21<6> ctp_wakeup = port:PB13<1><1> ;-------------------------------------------------------------------------------- ; CTP automatic detection configuration ;ctp_detect_used --- Whether startup automatic inspection function. 1:used,0:unused ;Module name postposition 1 said detection, 0 means no detection. ;-------------------------------------------------------------------------------- [ctp_list_para] ctp_det_used = 0 ft5x_ts = 0 gt82x = 0 gslX680 = 0 gt9xx_ts = 0 gt811 = 0 ;------------------------------------------------------------------------------- ;touch key configuration ;------------------------------------------------------------------------------- [tkey_para] tkey_used = 0 tkey_twi_id = 2 tkey_twi_addr = 0x62 tkey_int = port:PI13<6> ;------------------------------------------------------------------------------- ;motor configuration ;------------------------------------------------------------------------------- [motor_para] motor_used = 0 motor_shake = port:PB03<1><1> [gpio_para] gpio_used = 1 gpio_num = 2 gpio_pin_1 = port:PH20<1><1> gpio_pin_2 = port:PH10<0><0> [leds_para] leds_used = 1 leds_num = 4 leds_pin_1 = port:PH21<1><0> leds_name_1 = "blue:ph21:led1" leds_default_1 = 0 leds_trigger_1 = "heartbeat" leds_pin_2 = port:PH20<1><0> leds_name_2 = "orange:ph20:led2" leds_default_2 = 0 leds_trigger_2 = "cpu0" leds_pin_3 = port:PH11<1><0> leds_name_3 = "white:ph11:led3" leds_default_3 = 0 leds_trigger_3 = "cpu1" leds_pin_4 = port:PH07<1><0> leds_name_4 = "green:ph07:led4" leds_default_4 = 1 leds_trigger_4 = "mmc0" ;------------------------------------------------------------------------------- ;nand flash configuration ;------------------------------------------------------------------------------- [nand_para] nand_used = 1 nand_we = port:PC00<2> nand_ale = port:PC01<2> nand_cle = port:PC02<2> nand_ce1 = port:PC03<2> nand_ce0 = port:PC04<2> nand_nre = port:PC05<2> nand_rb0 = port:PC06<2> nand_rb1 = port:PC07<2> nand_d0 = port:PC08<2> nand_d1 = port:PC09<2> nand_d2 = port:PC10<2> nand_d3 = port:PC11<2> nand_d4 = port:PC12<2> nand_d5 = port:PC13<2> nand_d6 = port:PC14<2> nand_d7 = port:PC15<2> nand_wp = port:PC16<2> nand_ce2 = port:PC17<2> nand_ce3 = port:PC18<2> nand_ce4 = nand_ce5 = nand_ce6 = nand_ce7 = nand_spi = port:PC23<3> nand_ndqs = port:PC24<2> good_block_ratio = 0 ;------------------------------------------------------------------------------- ;disp init configuration ; ;disp_mode (0:screen0 1:screen1 2:two_diff_screen_diff_contents ; 3:two_same_screen_diff_contets 4:two_diff_screen_same_contents) ;screenx_output_type (0:none; 1:lcd; 2:tv; 3:hdmi; 4:vga) ;screenx_output_mode (used for tv/hdmi output, 0:480i 1:576i 2:480p 3:576p 4:720p50 5:720p60 6:1080i50 7:1080i60 8:1080p24 9:1080p50 10:1080p60 11:pal 14:ntsc) ;screenx_output_mode (used for vga output, 0:1680*1050 1:1440*900 2:1360*768 3:1280*1024 4:1024*768 5:800*600 6:640*480 10:1920*1080 11:1280*720) ;fbx format (4:RGB655 5:RGB565 6:RGB556 7:ARGB1555 8:RGBA5551 9:RGB888 10:ARGB8888 12:ARGB4444) ;fbx pixel sequence (0:ARGB 1:BGRA 2:ABGR 3:RGBA) --- 0 for linux, 2 for android ;lcd0_bright (lcd0 init bright,the range:[0,256],default:197 ;lcd1_bright (lcd1 init bright,the range:[0,256],default:197 ;------------------------------------------------------------------------------- [disp_init] disp_init_enable = 1 disp_mode = 0 screen0_output_type = 4 screen0_output_mode = 4 screen1_output_type = 0 screen1_output_mode = 4 fb0_width = 1024 fb0_height = 768 fb0_framebuffer_num = 2 fb0_format = 10 fb0_pixel_sequence = 0 fb0_scaler_mode_enable = 1 fb1_width = 1024 fb1_height = 768 fb1_framebuffer_num = 2 fb1_format = 10 fb1_pixel_sequence = 0 fb1_scaler_mode_enable = 0 lcd0_backlight = 197 lcd1_backlight = 197 lcd0_bright = 50 lcd0_contrast = 50 lcd0_saturation = 57 lcd0_hue = 50 lcd1_bright = 50 lcd1_contrast = 50 lcd1_saturation = 57 lcd1_hue = 50 ;------------------------------------------------------------------------------- ;lcd0 configuration ;lcd_dclk_freq: in MHZ unit ;lcd_pwm_freq: in HZ unit ;lcd_if: 0:hv(sync+de); 1:8080; 2:ttl; 3:lvds ;lcd_hbp: hsync back porch ;lcd_ht: hsync total cycle ;lcd_vbp: vsync back porch ;lcd_vt: vysnc total cycle *2 ;lcd_hv_if: 0:hv parallel 1:hv serial ;lcd_hv_smode: 0:RGB888 1:CCIR656 ;lcd_hv_s888_if serial RGB format ;lcd_hv_syuv_if: serial YUV format ;lcd_hspw: hsync plus width ;lcd_vspw: vysnc plus width ;lcd_lvds_ch: 0:single channel; 1:dual channel ;lcd_lvds_mode: 0:NS mode; 1:JEIDA mode ;lcd_lvds_bitwidth: 0:24bit; 1:18bit ;lcd_lvds_io_cross: 0:normal; 1:pn cross ;lcd_cpu_if: 0:18bit; 1:16bit mode0; 2:16bit mode1; 3:16bit mode2; 4:16bit mode3; 5:9bit; 6:8bit 256K; 7:8bit 65K ;lcd_frm: 0:disable; 1:enable rgb666 dither; 2:enable rgb656 dither ;lcd_gpio_0: SCL ;lcd_gpio_1 SDA ;------------------------------------------------------------------------------- [lcd0_para] lcd_used = 1 lcd_x = 1024 lcd_y = 600 lcd_dclk_freq = 51 lcd_pwm_not_used = 0 lcd_pwm_ch = 0 lcd_pwm_freq = 10000 lcd_pwm_pol = 1 lcd_max_bright = 240 lcd_min_bright = 64 lcd_if = 0 lcd_hbp = 158 lcd_ht = 1344 lcd_vbp = 25 lcd_vt = 1270 lcd_vspw = 3 lcd_hspw = 20 lcd_hv_if = 0 lcd_hv_smode = 0 lcd_hv_s888_if = 0 lcd_hv_syuv_if = 0 lcd_lvds_ch = 0 lcd_lvds_mode = 0 lcd_lvds_bitwidth = 0 lcd_lvds_io_cross = 0 lcd_cpu_if = 0 lcd_frm = 1 lcd_io_cfg0 = 0x00000000 lcd_gamma_correction_en = 0 lcd_gamma_tbl_0 = 0x00000000 lcd_gamma_tbl_1 = 0x00010101 lcd_gamma_tbl_255 = 0x00ffffff lcd_bl_en_used = 0 lcd_bl_en = port:PH07<1><0><1> lcd_power_used = 0 lcd_power = port:PH08<1><0><1> lcd_pwm_used = 0 lcd_pwm = port:PB02<2><0> lcdd0 = port:PD00<2><0> lcdd1 = port:PD01<2><0> lcdd2 = port:PD02<2><0> lcdd3 = port:PD03<2><0> lcdd4 = port:PD04<2><0> lcdd5 = port:PD05<2><0> lcdd6 = port:PD06<2><0> lcdd7 = port:PD07<2><0> lcdd8 = port:PD08<2><0> lcdd9 = port:PD09<2><0> lcdd10 = port:PD10<2><0> lcdd11 = port:PD11<2><0> lcdd12 = port:PD12<2><0> lcdd13 = port:PD13<2><0> lcdd14 = port:PD14<2><0> lcdd15 = port:PD15<2><0> lcdd16 = port:PD16<2><0> lcdd17 = port:PD17<2><0> lcdd18 = port:PD18<2><0> lcdd19 = port:PD19<2><0> lcdd20 = port:PD20<2><0> lcdd21 = port:PD21<2><0> lcdd22 = port:PD22<2><0> lcdd23 = port:PD23<2><0> lcdclk = port:PD24<2><0> lcdde = port:PD25<2><0> lcdhsync = port:PD26<2><0> lcdvsync = port:PD27<2><0> ;---------------------------------------------------------------------------------- ;lcd1 configuration ;lcd_dclk_freq: in MHZ unit ;lcd_pwm_freq: in HZ unit ;lcd_if: 0:hv(sync+de); 1:8080; 2:ttl; 3:lvds ;lcd_hbp: hsync back porch ;lcd_ht: hsync total cycle ;lcd_vbp: vsync back porch ;lcd_vt: vysnc total cycle *2 ;lcd_hv_if: 0:hv parallel 1:hv serial ;lcd_hv_smode: 0:RGB888 1:CCIR656 ;lcd_hv_s888_if serial RGB format ;lcd_hv_syuv_if: serial YUV format ;lcd_hspw: hsync plus width ;lcd_vspw: vysnc plus width ;lcd_lvds_ch: 0:single channel; 1:dual channel ;lcd_lvds_mode: 0:NS mode; 1:JEIDA mode ;lcd_lvds_bitwidth: 0:24bit; 1:18bit ;lcd_lvds_io_cross: 0:normal; 1:pn cross ;lcd_cpu_if: 0:18bit; 1:16bit mode0; 2:16bit mode1; 3:16bit mode2; 4:16bit mode3; 5:9bit; 6:8bit 256K; 7:8bit 65K ;lcd_frm: 0:disable; 1:enable rgb666 dither; 2:enable rgb656 dither ;lcd_gpio_0: SCL ;lcd_gpio_1 SDA ;---------------------------------------------------------------------------------- [lcd1_para] lcd_used = 0 lcd_x = 0 lcd_y = 0 lcd_dclk_freq = 0 lcd_pwm_not_used = 0 lcd_pwm_ch = 1 lcd_pwm_freq = 0 lcd_pwm_pol = 0 lcd_max_bright = 240 lcd_min_bright = 64 lcd_if = 0 lcd_hbp = 0 lcd_ht = 0 lcd_vbp = 0 lcd_vt = 0 lcd_vspw = 0 lcd_hspw = 0 lcd_hv_if = 0 lcd_hv_smode = 0 lcd_hv_s888_if = 0 lcd_hv_syuv_if = 0 lcd_lvds_ch = 0 lcd_lvds_mode = 0 lcd_lvds_bitwidth = 0 lcd_lvds_io_cross = 0 lcd_cpu_if = 0 lcd_frm = 0 lcd_io_cfg0 = 0 lcd_gamma_correction_en = 0 lcd_gamma_tbl_0 = 0x00000000 lcd_gamma_tbl_1 = 0x00010101 lcd_gamma_tbl_255 = 0x00ffffff lcd_bl_en_used = 0 lcd_bl_en = lcd_power_used = 0 lcd_power = lcd_pwm_used = 1 lcd_pwm = port:PI03<2><0> lcd_gpio_0 = lcd_gpio_1 = lcd_gpio_2 = lcd_gpio_3 = lcdd0 = port:PH00<2><0> lcdd1 = port:PH01<2><0> lcdd2 = port:PH02<2><0> lcdd3 = port:PH03<2><0> lcdd4 = port:PH04<2><0> lcdd5 = port:PH05<2><0> lcdd6 = port:PH06<2><0> lcdd7 = port:PH07<2><0> lcdd8 = port:PH08<2><0> lcdd9 = port:PH09<2><0> lcdd10 = port:PH10<2><0> lcdd11 = port:PH11<2><0> lcdd12 = port:PH12<2><0> lcdd13 = port:PH13<2><0> lcdd14 = port:PH14<2><0> lcdd15 = port:PH15<2><0> lcdd16 = port:PH16<2><0> lcdd17 = port:PH17<2><0> lcdd18 = port:PH18<2><0> lcdd19 = port:PH19<2><0> lcdd20 = port:PH20<2><0>